Janome Accessories

The ​​​​​​​Janome 1600P Tension Check Spring 767046006 can become bent and twisted over time. Threads can catch and wrap around it which, when pulled with a heavy hand, may cause damage. Here is the replacement.

The ​​​​​​​Janome 2 Pin Bulb 830999999 is quite a tough chap. However, delicate care must be taken when fitting. His tow 'pins' can bend quite easily.

The Janome Base Rubber 647009002 is found on a wide range of models. He's sometimes prone to going missing, especially if you keep your machine in a cupboard.

Here is a pack of ten ​​​​​​​Janome Bobbins 200122005. They fit the vast majority of Janome sewing machines. Including the front-loading and drop-in models.

he Janome Bulb Wedge Type 000026002 fits a very wide range of models. Usually this bulb will endure for many years, but all bulbs blow at some time.

Here is a set of ​​​​​​​Janome Cover Pro Tension Units. Each one has a particular colour to indicate their position on the machine. Priced individually.

The Janome Drive Belt 650166008 is quite a hard wearing type.​ However, problems can occur if the belt becomes loose. This can cause the motor pulley to spin and wear the teeth away.

The ​​​​​​​Janome Drive Belt 830276006 will last a very long time under normal circumstances. If however the belt becomes loose it may begin to wear.

This Janome Embellisher Fixed Needle Unit​​​​​​​ is the same one that comes with the Embellisher models Xpression and FM725

The ​​​​​​​Janome Embellisher Foot 725033000 is made of plastic. After prolonged use it may become worn or damaged. It may even go missing. Whatever the reason for your search, here is the replacement.

This Janome Embellisher Needle Kit allows you remove individual needles and replace them with new. Reducing your overall expense and inconvenience.

A pack of ten Janome Embellisher standard needles which can be used in the Janome Xpression and FM725.

The ​​​​​​​Janome Feed Dog 653193003 fits a few models commonly found in schools and colleges. So they may wear out from prolonged use on various 'materials'.

The ​​​​​​​teeth on the Janome Feed Dog 809149003 may lose their bite after years of hard service. If you've reached that stage then maybe it's time for a new feed dog.

The ​​​​​​​Janome Feed Dog 846063007 may well wear out sooner than various other models. The 6500P is often bought by commercial users and they are more likely to wear out a feed dog.

This is the ​​​​​​​Janome Hoop Frame Thumbscrew Complete and it is used on a variety of Janome embroidery hoops/frames. Eventually the thread wears out on either the thumbscrew or the nut.

The Janome Mast Top 846197001 Thread Guide will sometimes take off in the night, or you may even damage it. Those 6600's used in schools or wardrobe departments often contact us for a replacement.

The ​​​​​​​Janome MC6500p Handwheel may well suffer damage in the busy sewing studio or classroom. The four finger clips are only so strong. If they are forced too far, they will snap.

The ​​​​​​​Janome Motor Socket 739503009 is the new switched type. Motor sockets tend to fail only if they are used in very busy environments. The school classroom or the industrious studio or wardrobe department.

The ​​​​​​​Janome Motor Socket 852514007 is another socket which will, generally speaking, last a long time. The multi-user environment might shorten its lifespan. Here is the replacement.

The ​​​​​​​Janome Needle Bar 653503103 fits a wide range of models, so there's certainly more than an average chance someone is looking for this particular part. It comes complete with the needle clamp and thread guide.

The ​​​​​​​Janome Needle Bar 822658001 is perhaps one that is replaced more than most. This one fits models that have often been used in schools and colleges. So, damage and misuse may occur more frequently.

The ​​​​​​​Janome Needle Bar Clamp Thumbscrew 822055105 fits most of the 'top-loading' sewing and embroidery models. The point at the end can sometimes break or become worn flat.

The ​​​​​​​Janome Needle Bar Crank 808005003 can become work through excessive use and a lack of regular maintenance. Trapped threads can bind inside and cause wear and tear.

The ​​​​​​​Janome Needle Bar Crank Unit 846615000 fits the Janome 6500p which is often used semi-commercially. This being the case there is a chance that this part will eventually become worn and loose.

The ​​​​​​​Janome Needle Bar Frame 827026009 supports the needle bar and allows it to function. Only the heavy duty user is likely to cause substantial wear to this part.

The ​​​​​​​Janome Needlebar 858538005 is the type of part which never normally wears out. Of course there are always exceptions to every rule, so here is the replacement.

Janome Overlocker 1/8" Piping Foot

The ​​​​​​​Janome Race Body 735610101 fits most Janome front-loading models. The exceptions are the Jem and 1017. This part will only require replacing after years of very hard labour.

The ​​​​​​​Janome Small Spool Peg Cap 822019004 will fit the vast majority of Janome models with a horizontal plastic spool peg. In most cases the small spool peg cap is the best choice.

The ​​​​​​​Janome Spool Peg 505067005 is the horizontal fitting type, found on the modern Janome sewing machine. The old style verticle peg is gradually disappearing. This pin can often be snapped when lifting the machine.

The ​​​​​​​Janome Spool Peg 639003001 is a short and stout chap but he can break under pressure. Take care when fitting and remember not to grab the spool peg when lifting the machine.

The ​​​​​​​Janome Spool Peg 652205109 is a more traditional vertical spool peg. It is held in place by a small metal clip which often drops down inside your machine if you pull the peg out.

The ​​​​​​​Janome Spool Peg 659067005 should be handled with care. When the machine is wearing its cover, it's easy for the hand that slides in to catch the handle to grab the spool peg instead.

The ​​​​​​​Janome Spool Peg 660005009 fits the old Jem range of Janome sewing machines. They were always popular as a club machine, mainly by quilters who took them to their quilt clubs. 

The ​​​​​​​Janome Spool Peg 660005010 fits just the one model, the JP760. Take care when fitting.

The ​​​​​​​Janome Spool Peg 722003002 is the twin peg type. It is easily fitted to the back of the machine and is held in place with a screw. This spool peg fits the Janome RX18S model.  

The ​​​​​​​Janome Spool Peg 724206106 is fitted to the Janome MyStyle 22 which, as many teachers will know, is a model found in many schools and colleges.

The ​​​​​​​Janome Spool Peg 731006106 is another twin-peg type that screws onto the back of the machine. So it's very easy to replace. It fits a range of good quality basic Janome models.

The ​​​​​​​Janome Spool Peg 797051007 fits the Janome 1200D Coverlock machine. This type of push-in spool peg can snap at its fixing point. Or it may be pulled from its fitting and then lost.

The ​​​​​​​Janome Spool Peg 809027004 will fit the following models, TXL607 DKS300 DKS100 MC500E MXL50 MC400E. It is a stock item so usually it will be posted out on the same day you place your order.

The ​​​​​​​Janome Spool Peg 856007004 is designed to fit just one model, the Janome MC200E. Like all horizontal spool pegs, care must be taken when you lift or carry the machine.

The ​​​​​​​Janome Spool Peg 859052003 is yet another 'pivot type'. This type of spool peg is often damaged when lifting or transporting the machine.

The ​​​​​​​Janome Spool Peg Metal Screw-in was used on many of the old Newhome and Janome models. From day one most sewing machines were fitted with either a tapered 'knock-in' spool peg, or this screw-in type.

The ​​​​​​​Janome Spool Peg Sleeve 652018103 sits inside the top of the sewing machine and holds the spool peg in place. He's quite a robust chap and doesn't usually wear out or suffer damage but...

The ​​​​​​​Janome Tension Unit 731508000 is a part we seldom replace. However, it is a part we keep in stock, just in case. The last one we did replace was a result of vandalism in a school textiles classroom.

The Janome Thumbscrew 850801307 helps to clamp certain Janome embroidery hoops and frames. The thread on the thumbscrew will gradually wear until you can't tighten the nut.

The ​​​​​​​Janome Thumbscrew Nut 000218601 may wear out or he might go missing. Whatever the problem, here is the replacement. He fits the thumbscrew for the embroidery frame on the MC200E

The ​​​​​​​Janome Thumbscrew Spring 718844309 doesn't generally wear out but he may go missing. Undo the nut and 'ping' off he goes under the sideboard. Not to worry, here is the replacement.

The ​​​​​​​Janome Top Thread Guide 654633003 is located inside the top thread guide cover. It's usually the sort of part that only suffers damage in schools. Too heavy a hand might lead to problems.

The ​​​​​​​Janome Top Thread Guide Body 650503506 sits on top of the machine and holds the bobbinwinder tension unit on top, and the top thread guide (not included) inside.