Brother PR Spares

Brother PR model embroidery machine owners require a reliable supplier. Not just for new machines or service and repair work, but for parts too. Here at Bambers we know which parts you will be searching for most. So we keep them all in stock, for a speedy and reliable service.
​​​​​​​
Showing 38 of 38 results
  • Brother PR Bobbincase

    Brother PR Bobbincase

    £29.80
    Your Brother PR Bobbincase is an extremely vital part. It is also very easily damaged if you drop it and possibly tread on it. So ALL Brother PR owners should have at least one spare
  • Brother PR600-650 Motor

    Brother PR600-650 Motor

    £72.59
    A replacement motor for the Brother PR series of embroidery machines. It will fit the PR600, PR620 & PR650.
  • Brother PR655/670e Motor

    Brother PR655/670e Motor

    £69.00
    This Brother PR655/670 motor is designed to be used in the Brother PR655 embroidery machine. You will notice the shorter mains cable. However, like the other motor, this one is designed
  • Brother PR Frame Collar

    Brother PR Frame Collar

    £4.28
    The Brother PR Frame Collar is only a small chap but he plays a vital part. He sits inside each of the outer frames and enables you to 'tighten-up' each frame. If you remove the long thin
  • Brother PR Embroidery Frame Spring

    Brother PR Embroidery Frame Spring

    £4.00
    The Brother PR embroidery frame spring fits over the the thumbscrew used to tighten and loosen your embroidery frames. They don't really wear out but they do tend to ping off into orbit when you are
  • Brother PR Fixed Knife & Clip

    Brother PR Fixed Knife & Clip

    £15.99
    This is the Brother PR Fixed Knife & Clip. Over time and with continued use the fixed knife becomes blunt and causes various problems with your work. We sell this replacement with a new clip to
  • Brother PR Needle Threader

    Brother PR Needle Threader

    £12.99
    This is the replacement needle threader for your Brother PR embroidery machine. Eventually all needle threaders either bend or wear out. You can of course still thread your needles by hand.
  • Brother PR Needleplate

    Brother PR Needleplate

    £33.99
    A replacement Brother PR Needleplate. The heavy duty PR user will, after some time, possibly damage their Brother PR needlplate. Bent needles can chip away at the hole in the plate which can lead
  • Brother PR Needleplate Screw

    Brother PR Needleplate Screw

    £1.24
    A spare screw for the needleplate on your Brother PR embroidery machine. It's not usually the sort of part that wears out. Sometimes though the head can split.
  • Brother PR Race Door Spring

    Brother PR Race Door Spring

    £3.00
    The Brother PR Raceway door spring sometimes snaps, or goes missing. Prolonged use can wear out the spring and you find the door won't fully close. Here is the replacement. It's one of our stock items,
  • Brother PR Raceway Door

    Brother PR Raceway Door

    £2.64
    The Brother PR Raceway Door will eventually fail. The small hinge on your Brother PR Raceway Door often fails after years of continued use. The spring which holds the door in place can also lose it's torsion,
  • Brother PR Base Rubber

    Brother PR Base Rubber

    £1.99
    The Brother PR base rubber will sometimes go missing, especially if you're the type to move your PR around a bit. Maybe you take it out on the road, to shows etc. Here is the replacement you've been looking
  • Brother PR Small Thumbscrew

    Brother PR Small Thumbscrew

    £3.13
    The job of the Brother PR small thumbscrew is to keep the embroidery frame arm fixed in place. Always ensure he's tight otherwise your PR will think you're working with a different sized embroidery frame.
  • Brother PR Large Thumbscrew

    Brother PR Large Thumbscrew

    £3.30
    his is the larger thumbscrew that holds the embroidery frame bracket in place on your Brother PR embroidery machine. Please don't confuse him with his smaller brother
  • Brother PR Screwdriver

    Brother PR Screwdriver

    £4.99
    Use this Brother PR6 Z screwdriver to easily remove the two screws in the needleplate on your Brother PR6 embroidery machine. It's important to remove the needleplate every once in a while.
  • Set of Six Brother PR Needle Screws

    Set of Six Brother PR Needle Screws

    £2.69
    Here is a Set of Six Brother PR Needle Screws. Firstly their main job is to hold each needle in place. Secondly, if you drop one chances are you will never find it again. Furthermore it isn't a bad idea to replace t
  • Brother PR Needle Screw Screwdriver

    Brother PR Needle Screw Screwdriver

    £2.06
    Use the Brother PR Needle Screw Screwdriver XC5159051 to loosen or tighten the needle screw. You really only need half a turn to loosen and, when you tighten, you don't need to be too excessive.
  • Brother PR Cap Frame Inset

    Brother PR Cap Frame Inset

    £2.50
    If you use a cap attachment on your Brother PR model. You will find this Brother PR Cap Frame Inset will help your caps slide over the needleplate more easily and will be better supported.
  • Brother PR Cap Frame Clip

    Brother PR Cap Frame Clip

    £3.66
    Use the Brother PR Cap Frame Clip to hold baseball caps in place on the cap frame. Embroidering caps can be a little bit tricky and time consuming and sometimes these clips will help you stretch the cap
  • Brother PR Cap Frame Screw

    Brother PR Cap Frame Screw

    £0.99
    These ​​​​​​​Brother PR Cap Frame Screws are small but vital. Don't confuse them with the slide studs. These screws may come loose if you use the cap frame on a regular basis. The vibration of the machine
  • Brother PR Drive Belt

    Brother PR Drive Belt

    £8.10
    Here is the replacement Brother PR Drive Belt. When you fit the new belt please ensure there isn't too much slack. Also, it shouldn't be too tight. Just a nice even tension. If the belt slips,
  • Brother PR Fixed Knife Screw

    Brother PR Fixed Knife Screw

    £1.66
    The Brother PR Embroidery Fixed Knife Screw holds the fixed knife in place. It's important to check, clean and replace the fixed knife on a regular basis.
  • Brother PR Hoop Sensor Assembly XC6177051

    Brother PR Hoop Sensor Assembly XC6177051

    £38.65
    A common fault with all Brother PR models is suddeenly losing frame size detection. If you carry out the AD test and your machine still can't detect which size frame you're using, chances are you need a new Hoop Sensor.
  • Brother PR Motor Fan XA9652150

    Brother PR Motor Fan XA9652150

    £1.25
    We always like to keep a number of the Brother PR Motor Fans (XA9652150) in stock. They can sometimes suffer damage and lose the odd blade here and there.
  • Brother PR Movable Knife Spacer Shims

    Brother PR Movable Knife Spacer Shims

    £0.49
    The ​​​​​​​Brother PR Movable Knife Spacer Shims do exactly what they suggest. Use them to correctly adjust the height of the movable knife. Clear any congealed fluff or cotton from around the knife first.
  • BROTHER PR MOVEABLE KNIFE

    BROTHER PR MOVEABLE KNIFE

    £44.99
    The Brother PR Moveable Knife Assembly includes the knife and the four spacer shims. The two knives, fixed and moveable, can become worn and blunt over time.
  • Brother PR Moveable Knife Collar

    Brother PR Moveable Knife Collar

    £0.75
    The ​​​​​​​Brother PR Moveable Knife Collar keeps the knife in position. This part is quite robust and will only fail under unusual circumstances. Then again. We've seen hundreds of Brother PR models in our workshop,
  • Brother PR Moveable Knife Screw

    Brother PR Moveable Knife Screw

    £12.50
    The Brother Moveable Knife screw shouldn't really wear but you might lose it. Whatever the case may be, if you need one, here it is.
  • Brother PR O Ring XE8376001

    Brother PR O Ring XE8376001

    £1.25
    The ​​​​​​​Brother PR O Ring XE8376001 fits over the rear thread tube on your Brother PR embroidery machine. They tend to perish and crack after some time, especially if they face direct sunlight.
  • Brother PR Pipe Bush XC5812051

    Brother PR Pipe Bush XC5812051

    £0.75
    The ​​​​​​​Brother PR Pipe Bush fits into the thread mast on your Brother PR machine. It aids the smooth flow of thread as it passes through the mast. The heavy duty user may find this part wears
  • Brother PR Protective Cap XC5740151

    Brother PR Protective Cap XC5740151

    £1.25
    This chap has a smooth and domed surface. His task in life is to enable the threads to slip over him when your PR changes colour. A small but pivotal role that goes unnoticed, until he goes missing.
  • Brother PR Threading Tool XE8362001

    Brother PR Threading Tool XE8362001

    £4.65
    The ​​​​​​​Brother PR Threading Tool XE8362001 is a handy device for all PR users. The notched end will hold the thread while you thread up the machine.
  • Brother PR Wiper Hook XC5981151

    Brother PR Wiper Hook XC5981151

    £6.99
    The replacement wiper hook for your Brother PR embroidery machine. It fits all models and care should be taken when fitting.
  • Brother PR1055X Motor

    Brother PR1055X Motor

    £67.00
    Here is the replacement Brother PR1055X motor. As this motor has a different cable configuration you should only use this motor on the PR1055X. Please do not use it on any other six or ten needle model.